Shiro Telephone SC3123 User Manual

User Manual •  
SC3123  
Caller ID Phone  
 
SC3123 User Guide  
TABLE OF CONTENT  
PRODUCT OVERVIEW.....................................................................................3  
1. INSTALLING OR REPLACING THE BATTERY .........................................................4  
2. SWITCH OPERATION...................................................................................4  
IDD LOCK switch.......................................................................................4  
3. SOFTWARE SETTING ..................................................................................4  
4. FUNCTION KEY OPERATION ..........................................................................6  
UP and DOWN key.....................................................................................6  
OUT key ................................................................................................6  
DEL key .................................................................................................6  
PAUSE key ..............................................................................................6  
IP key ...................................................................................................6  
FLASH (600ms) / RING key...........................................................................6  
AUTO-RD REDIAL/BACK key..........................................................................6  
HF (HANDSFREE) key..................................................................................6  
5. ADDITIONAL NOTES ...................................................................................7  
INCOMING CALL LCD INDICATOR.....................................................................7  
LCD BACKLIGHT FUNCTION ..........................................................................7  
TROUBLESHOOTING GUIDE..............................................................................7  
DECLARATION OF CONFORMITY ........................................................................8  
2
 
SC3123 User Guide  
PRODUCT OVERVIEW  
14  
15  
16  
1
2
3
4
5
13  
6
12  
11109 8 7  
Description:  
1. LCD Display  
2. SET key  
11. UP key  
12. OUT key  
3. IP key  
13. Handset Cord jack  
14. LINE OUT (TEL) jack  
4. FLASH/RING key  
5. AUTO-RD REDIAL/BACK key 15. LINE IN (TEL) jack  
6. HF (HANDSFREE) key  
7. 0-9/#/* key  
8. PAUSE key  
16. LOCK switch  
9. DOWN key  
10. DEL key  
3
 
SC3123 User Guide  
1. INSTALLING OR REPLACING THE BATTERY  
Install 3 Alkaline AA batteries into the battery compartment and re-fit the cover before use.  
IMPORTANT—before removing the battery compartment cover, ensure the base unit  
is disconnected from the telephone line.  
Connection and conditions for use  
You can connect your SC3123, to public networks in the United Kingdom or to an  
approved PBX using DTMF signaling. Each item of telephone equipment (phones, fax  
machines, etc.) has a ringer equivalence numbers (REN). The RENs of all  
equipment connected to an exchange line must not add up to more than 4  
otherwise, one or more phones may not ring and/or answer calls correctly.  
SC3123 has a REN of 1, and most other telephones have a REN of 1 unless marked  
otherwise.  
2. SWITCH OPERATION  
IDD LOCK switch  
Use the keys provided in the package. The telephone allows all outgoing number if the key is  
on red point. It cannot dial outgoing number starting with digit 0 when the key is on green  
point.  
3. SOFTWARE SETTING  
Press the SET key to enter menu setting. The LCD panel will display SET 1 DATE, press the  
UP/DOWN key to select the different options. Press the SET key again to confirm. Use the  
UP/DOWN key to select the mode you need. After completing the setting, press the SET key  
to go to next item. To exit menu, press the DEL key.  
By pressing the SET key in the ‘on-hook’ mode, you can select the following:  
SET ITEM  
OPERATIONS  
DATE/TIME  
LCD displays SET 1 DATE, press the SET key to enter this mode. The  
4
 
SC3123 User Guide  
year value would flash, use the UP/DOWN key to select value. Press the  
SET key to enter into next item.  
AREA CODE  
LCD display SET 2 CODE, press the SET key to confirm. LCD will display  
CODE, press the SET key to enter this mode. Use the UP/DOWN key to  
select value. Press the SET key to enter into next item.  
Area Code can be used to filter the number for incoming calls. E.g.  
Area code = 75 when there’s incoming call with 75 6554556, it will be  
displayed as 655 4556 only.  
LONG CODE  
LCD display SET 3 LCODE, press the SET key to enter this mode. LCD  
will displays LCODE, use the UP/DOWN key to select value. Press the  
SET key to enter into next item.  
To activate this feature, while checking incoming calls using UP key,  
press REDIAL key twice to add the LONG DIST ACCESS code in front of  
the number.  
FLASH TIME  
AUTO-IP  
LCD display SET 4 FLASH, press the SET key to enter this mode. Use  
the UP/DOWN key to select value. Press the SET key to enter into next  
item.  
LCD display SET 5 IP, press the SET key to enter this mode. LCD will  
display AUTO IP OFF and OFF will flashes, use the UP/DOWN key to  
select value. When LCD displays AUTO IP ON, press SET key. The LCD  
will display INPUT CODE for you to enter the IP numbers. Use the DEL  
key to correct any wrong input. After entering all IP number, press the  
SET key to enter into next item. The outgoing call will automatically  
use IP mode.  
Auto IP allows you to replace a sequence of number with single 0. E.g.  
Setting 1455 as Auto IP, therefore when you need to dial 1455, just put  
0 in front (pre-dial mode), 0 2334565 will be dialed as 1455 2334565.  
P/T MODE  
ALARM  
LCD display SET 6 P-T, press the SET key to enter this mode. LCD will  
display TONE. Use the UP/DOWN key to change it into PULSE. Press  
SET key to enter into next item.  
LCD display SET 7 ALARM, press the SET key to enter this mode. LCD  
will display ALARM OFF, which will turn the alarm off. Use the  
UP/DOWN key to select ON or OFF.  
This feature is to ensure other telephone is unable to share the same  
line as your telephone. If another telephone is sharing the same line,  
there will be constant noise when it is off hook.  
5
 
SC3123 User Guide  
4. FUNCTION KEY OPERATION  
UP and DOWN key  
In any mode, press the UP/DOWN key to check all the incoming numbers. If there is no  
incoming call, LCD will display END. The unit can receive up to 16-digit number.  
OUT key  
In any mode, check outgoing numbers by pressing the OUT key. Use the UP/DOWN key to  
select the outgoing number. Press the REDIAL key to dial the selected number.  
DEL key  
When checking incoming and outgoing call in any mode, press the DEL key to delete the  
number you are checking. Press the DEL key for 4 sec to delete all incoming or outgoing call  
numbers. When you pre-dial, press the DEL key to delete one digit at a time. When you enter  
the IP number or password, use the DEL key to delete error digit.  
PAUSE key  
To insert a 3.6 second of pause while dialing, press PAUSE key and it will display P on the LCD  
panel.  
IP key  
- When auto IP function is off:  
In the ‘on-hook’ mode, pre-dial the phone number followed by the IP key. The unit will be  
on-hook automatically and dial the number with the IP number. (Note: The IP function cannot  
be used when the lock is set to lock “0”.)  
- When auto IP function is on:  
In the ‘on-hook’ mode, pre-dial the phone number followed by the REDIAL/BACK key. The  
unit will off-hook automatically and dial the number with IP mode if the first digit number is  
“0”.  
FLASH (600ms) / RING key  
In the ‘on-hook’ mode, press the FLASH/RING key. The LCD will display TONE 1-4 for four  
selectable ringing tones. Select the preferred ringing tone by pressing the FLASH/RING key.  
When LCD panel displays TONE OFF, it means the ringing tone is turned off.  
For FLASH function:  
In the on-hook mode, press this key to auto-hang up for 600ms, after that you can press  
REDIAL key or dial out another number.  
AUTO-RD REDIAL/BACK key  
In the ‘on-hook’ mode, press this key to redial the last called number.  
HF (HANDSFREE) key  
While on-hook, press the HF key to go into handsfree mode. You can talk through the  
6
 
SC3123 User Guide  
microphone and listen from the speakerphone without lifting the handset. While off-hook,  
press the HF key and put down the handset to go into handsfree mode.  
5. ADDITIONAL NOTES  
INCOMING CALL LCD INDICATOR  
When there is incoming call, the unit will be automatically display the caller number, date  
and time, and also display its serial number. If the incoming call is in private mode, it will  
display “__p__”; it will display “__0__” if exchange cannot determine the number; it will  
display “—E—“ if the call signal contains error.  
LCD BACKLIGHT FUNCTION  
When there is incoming call or handset is off-hook, the LCD backlight will lit up. It will be on  
for about 6 seconds before going off. Without batteries, LCD backlight will not lit up at all.  
TROUBLESHOOTING GUIDE  
(Q) I do not hear any dial tone from the handset.  
(A) Ensure the handset cord is connected correctly from the handset to the handset cord jack  
at the base. Ensure you have plug in the telephone cable from the telephone to the wall  
socket correctly. If the problem persists, please check with your local dealer.  
(Q) I could not see the caller’s number on the LCD when there is incoming call.  
(A) Ensure that you have subscribed Caller ID service from your local telecom provider.  
(Q) There is no LCD Display / Backlight after I have connected the telephone line. I can  
call out normally.  
(A) Ensure that you have inserted the batteries on the battery compartment. If there is still  
no display, change the batteries and ensure it is not empty. If the problem persists, please  
check with your local dealer.  
7
 
SC3123 User Guide  
DECLARATION OF CONFORMITY  
The telephone complies with the essential protective requirements and objectives of:  
EC R& TTE Directive 1999/5/EC  
EC Low Voltage Directive 73/23/EEC  
EC EMC Directive 89/336/EEC  
And conforms to the following relevant harmonized standards:  
EMC: EN55022, EN55024  
Safety: EN 60950  
Created on 28th October 2005. SC3123 Caller ID Phone.  
Please visit us at www.shirocorp.com.  
8
 

Sharp Camcorder VL Z400H T User Manual
Sherwood Speaker ST 3103 User Manual
Shindaiwa Saw 68002 94310 User Manual
Sony Camcorder CCD TR315E User Manual
Sony PDAs Smartphones PEG SJ33 User Manual
Sony Portable CD Player CFS 1055L User Manual
Sony Portable Speaker SRSPC51 User Manual
StarTechcom Network Card PCI2S650PW User Manual
Sunbeam Iron SR8600 User Manual
Sylvania DVD Player SDVD8716D User Manual